Less hassle. More benefits.

The V10 Air Plasma Sterilizer uses just air and electricity to safely and easily sterilize critical veterinary instruments at least 3 times faster than ethylene oxide, increasing productivity and throughput.

LOW TEMPERATURE

Heat-sensitive instruments will not be damaged

LOW PRESSURE

Even the most delicate instruments can be sterilized without damage

LOW COST PER CYCLE

Only $3 to $5 per cycle

LOW MAINTENANCE

Only 1 minute of maintenance after every 15 sterilization cycles

NO INSTALLATION COSTS

No exterior ventilation is required

BROAD COMPATIBILITY

Compatible with most medical plastics, elastomers, and metals

NO HARMFUL BYPRODUCTS

Sterilant gases are converted back into air after sterilization

NO CHEMICAL CONSUMABLES

Air and electricity are the only inputs

LOW POWER

Requires about one-fourth the power of a similarly sized steam autoclave

Simple process. Zero emissions.

A single sterilization cycle is used for all compatible instruments. Once instruments are loaded into the sterilization chamber, simply press start to begin the process.

Air Plasma Sterilization® consists of the following 3 steps:

PRECONDITIONING

Air temperature, pressure, and humidity are optimized inside the sterilization chamber for reliable and repeatable performance.

15 to 20 minutes

STERILIZING

Preconditioned air is converted by plasma into reactive oxygen and nitrogen species that rapidly kill microorganisms on instrument surfaces.

3 hours

VENTILATING

Sterilant gases are pumped through a catalyst and adsorbent material that converts the gas back into harmless breathable air.

45 minutes

Preconditioning time varies based on relative humidity, temperature, and atmospheric pressure.

Fewer consumables. Higher productivity.

Each consumable is easy to replace, has no disposal restrictions, and can be stored indefinitely in the original packaging. The touchscreen will alert the user when it is time to replace a consumable.

DESICCANT

PB_Product_0320_BLE_8786

The desiccant canister is used during the preconditioning step to reduce relative humidity in the sterilization chamber.

Replaced every 50 to 75 cycles

PLASMA SHEET

PB_Sheet_Small

Plasma is produced on the surface of the plasma sheet inside the sterilization chamber, converting air into highly oxidative sterilant gases.

Replaced every 15 cycles 

CATALYST

PB_Product_0320_BLE_8788-2

The catalyst canister is used during the ventilation step to convert sterilant gases back into air.

Replaced every 200 cycles

Desiccant life varies based on relative humidity.

Easy installation. Advanced performance.

front_dimensions
side_dimensions
specs3

Exterior dimensions

28.75 in x 19.25 in x 18.75 in

Installation space requirement

30.75 in x 21.25 in x 20.75 in

Sterilization chamber dimensions

18 in x 16 in x 7 in

Storage temperature

-25-60 °C (-13-140 °F)

Operating temperature

5-40 °C (41-104 °F)

Electrical requirements

110-120 VAC, 50/60Hz, 6.5 A max

Sterilization tray dimensions∗

16 in x 10 in x 4 in

Sterilization tray volume

10.5 L (2.8 gal)

Weight

110 lbs (49.9 kg)

Items being sterilized must fit completely within the sterilization tray. Do not operate without the sterilization tray in place.

What Our Customers Say

“The Plasma Bionics sterilizer is a game changer for sterilization of heat-sensitive instruments. We can now sterilize plastic instruments that we would normally do short heat cycles on using plasma energy to greatly prolong the life of those instruments decreasing the overall cost to the patient to perform procedures. Tyvek™ based gowns can now be re-sterilized several times, as well as partially used staple guns, and expensive endoscopic surgical instruments.  The sterilizer is quiet, low-cost per load, and very simple to use. I highly recommend this product to anyone considering ethylene oxide sterilization or someone just needing a gentler sterilization technique for certain instruments in the everyday veterinary practice.”

Jeff Mayo, DVM, DABVP, C/F

Mayo Vet Services, Lynnwood, WA 

"I've used and provided feedback on Plasma Bionics' sterilization system from the prototype stage to market. It continues to be a cornerstone of keeping my sensitive equipment ready and safe for my patients. Easy to use, non-toxic, and with a minimal time and labor investment for a single-doctor practice, the machine pays for itself in terms of ease of use and cost per cycle and consumables. I would not make a switch to any other unit."

Christopher Stevens, DVM

Baton Rouge, LA

Email:
info@plasmabionics.com

Address:
Plasma Bionics LLC

1414 S Sangre Rd, Suite 101
Stillwater, OK 74074